Product namePS-500
Connected to the discharge waterway of an inverter pump, and applies electricity to the rotational speed control circuit
This sensor controls a pump's rotational speed to the keep discharge pressure consistent
This sensor controls a pump's rotational speed to the keep discharge pressure consistent
Basic Characteristics
| Product summary | Pressure sensor |
|---|---|
| Product purpose | Pressure control for inverter pumps |
| Intended use | Automatic water pumps for apartments and buildings, and compact pumps |
| Operating type | Its detector that uses semiconductor pressure sensors and its built-in electronic circuit convert pressure changes in fluid into voltage or current output signals. |
| Compatible standard | RoHS compliant |
Mechanical Characteristics
| Outer dimensions | φ43×70 |
|---|---|
| Case material | Case: ABS |
| Operating temperature range | -10～70℃ |
| Connection terminal type | R3/8 (PT3/8) female screw |
| Product mounting method | Pressure: Tighten the R3/8 (PT3/8) thread to a male screw |
Electrical Characteristics
| Rated voltage | Voltage output type: 9 to 13.2 VDC |
|---|---|
| Withstand voltage | 1800 VAC for 1 second |
| Insulation resistance | 500 VDC megohmmeter |
Characteristics Unique to This Product
- Output voltage 1 to 5 VDC, or output current 4 to 20 mA DC
- Pressure resistance: 3 MPa
- Load resistance Voltage output type: 5kΩ or higher Current output type: 200Ω or lower
- Current consumption Voltage output type: 18 mA or less Current output type: 40 mA or less
- Accuracy ±1.5% F.S or less (25°C) ±3% F.S or less (-10°C to 70°C)
- Impressed pressure 0 to 0.98 MPa
- Endurance: 2 million cycles
Product nameAL-100
Connected to the discharge waterway of a pump and accumulates pressure to reduce water hammer and pressure drops due to water leaks from pipes.
Basic Characteristics
| Product summary | Prevents pumps inching |
|---|---|
| Product purpose | Accumulate pressure and absorb pulsations and impact pressure of small pumps |
| Intended use | Prevent inching, attenuate pulsation, mitigate pressure fluctuations, and reduce water hammer |
| Operating type | Accumulate fluid by compressing nitrogen gas enclosed in the rubber bladder |
| Compatible standard | RoHS compliant |
Mechanical Characteristics
| Outer dimensions | φ 105×184 |
|---|---|
| Case material | Case: SPCE |
| Operating temperature range | -20～40℃ |
| Connection terminal type | G1/2 (PF1/2) male screw O-ring seal |
| Product mounting method | Pressure: Tighten the G1/2 (PF1/2) male screw into a female screw |
Characteristics Unique to This Product
- Compatible solution: Tap water, well water, and clean water for factories
- Contained gas: Nitrogen gas
- Maximum working pressure: 0.44 MPa
- Capacity: 1.0 L
Product nameAL-300
Connected to the discharge waterway of a pump and accumulates pressure to reduce water hammer and pressure drops due to water leaks from pipes.
Basic Characteristics
| Product summary | Prevents small inverter pumps from inching |
|---|---|
| Product purpose | Accumulate pressure and absorb pulsations and impact pressure of small pumps |
| Intended use | Prevent inching, attenuate pulsation, mitigate pressure fluctuations, and reduce water hammer |
| Operating type | Accumulate fluid by means of nitrogen gas enclosed in the rubber bladder, and by springs and resin products placed above the diaphragm. |
| C8 | RoHS compliant |
Mechanical Characteristics
| Outer dimensions | φ 85.4×72.5 |
|---|---|
| Case material | Case: SPCE |
| Operating temperature range | -20～90℃ |
| Connection terminal type | G1/2 (PF1/2) male screw O-ring seal |
| Product mounting method | Pressure: Tighten the G1/2 (PF1/2) male screw into a female screw |
Characteristics Unique to This Product
- Compatible solution: Tap water, well water, and clean water for factories
- Contained gas: Nitrogen gas
- Maximum working pressure: 0.5 MPa
- Capacity: 0.07 L
Product namePS-701
Mounted on the discharge waterway of a pump, and electrically connected in parallel to an AC power line
Turns on/off a pump in accordance with the pressure switch that is turned on and off depending on the pressure value
Turns on/off a pump in accordance with the pressure switch that is turned on and off depending on the pressure value
Basic Characteristics
| Product summary | Turns a pump on and off (for household use) |
|---|---|
| Product purpose | Detect a pump's discharge pressure and automatically start/stop it |
| Intended use | Detect a pump's discharge pressure |
| Operating type | Consists of a pressure-receiving area, contact circuit area, switch quick-operating mechanism, and pressure adjustment mechanism |
| Compatible standard | RoHS compliant |
Mechanical Characteristics
| Outer dimensions | Φ 53×83 |
|---|---|
| Case material | Cover: ABS |
| Operating temperature range | -20～80℃ |
| Connection terminal type | G3/8 (PF3/8) female screw |
| Product mounting method | Pressure: Insert the seal into the G3/8 (PF3/8) female screw, and tighten it to a male screw |
Electrical Characteristics
| Rated voltage | AC 125/250V |
|---|---|
| Rated capacity | 400/750W |
| Contact withstand count | 1 million times |
| Withstand voltage | 1500 VAC for 1 minute or 1800 VAC for 1 second |
| Insulation resistance | 500 VDC megohmmeter 10 MΩ or higher |
Characteristics Unique to This Product
- Pressure adjustment range: 0.069 to 0.343 MPa
- Maximum working pressure: 0.345 MPa
- Compatible solution: Tap water, well water, and clean water for factories
Product namePS-104/104DS
Mounted on the discharge waterway of a pump, and electrically connected in parallel to an AC power line
Turns on/off a pump in accordance with the pressure switch that is turned on and off depending on the pressure value
Turns on/off a pump in accordance with the pressure switch that is turned on and off depending on the pressure value
Basic Characteristics
| Product summary | Turns a pump on and off (for household use) |
|---|---|
| Product purpose | Detect a pump's discharge pressure and automatically start/stop it |
| Intended use | Detect a pump's discharge pressure |
| Operating type | Consists of a pressure-receiving area, contact circuit area, switch quick-operating mechanism, and pressure adjustment mechanism |
| Compatible standard | Electrical Appliances and Materials Safety Act RoHS compliant |
Mechanical Characteristics
| Outer dimensions | Φ 53×83 |
|---|---|
| Case material | Cover: ABS |
| Operating temperature range | -20～80℃ |
| Connection terminal type | R,G1/4(PT,PF1/4) R,G3/8(PT,PF3/8) female screws |
| Product mounting method | Pressure: Tighten the above female screw into a male screw |
Electrical Characteristics
| Rated voltage | AC 125/250V |
|---|---|
| Rated capacity | 400/750W |
| Contact withstand current | Rush 16.7 A / Breaking 6 A |
| Contact withstand count | 1 million times |
| Withstand voltage | 1500 VAC for 1 minute or 1800 VAC for 1 second |
| Insulation resistance | 500 VDC megohmmeter 10 MΩ or higher |
Characteristics Unique to This Product
- Pressure adjustment range: 0.069 to 0.343 MPa
- Maximum working pressure: 0.345 MPa
- Compatible solution: Tap water, well water, and clean water for factories
Product namePS-57
Mounted on the discharge waterway of a pump, and electrically connected in parallel to an AC power line
Turns on/off a pump in accordance with the pressure switch that is turned on and off depending on the pressure value
Turns on/off a pump in accordance with the pressure switch that is turned on and off depending on the pressure value
Basic Characteristics
| Product summary | Turns a pump on and off (for water tank) |
|---|---|
| Product purpose | Detect a pump's discharge pressure and automatically start/stop it |
| Intended use | Detect a pump's discharge pressure, and pressure inside a water tank |
| Operating type | Consists of a pressure-receiving area, contact circuit area, switch quick-operating mechanism, and pressure adjustment mechanism |
| Compatible standard | Electrical Appliances and Materials Safety Act RoHS compliant |
Mechanical Characteristics
| Outer dimensions | 67×95×185 |
|---|---|
| Case material | Cover, case: iron |
| Operating temperature range | 0～80℃ |
| Connection terminal type | R3/8 (PT3/8) male screw |
| Product mounting method | Pressure: Tighten the R3/8 (PT3/8) male screw into a female screw |
Electrical Characteristics
| Rated voltage | AC 125/250V |
|---|---|
| Rated capacity | 400/750W |
| Contact withstand count | 1 million times |
| Withstand voltage | 1500 VAC for 1 minute or 1800 VAC for 1 second |
| Insulation resistance | 500 VDC megohmmeter 10 MΩ or higher |
Characteristics Unique to This Product
- Pressure adjustment range: 0.098 to 0.980 MPa
- Maximum working pressure: 0.98 MPa
- Compatible solution: Tap water, well water, and clean water for factories
Inquiries about Control product
